Expandable 1–16 detector channels
Modular controller design accepts 1–16 compatible detectors using three-wire 4–20 mA input or RS-485 bus communication.
Product ImageRD3000E Gas Leakage Detection Alarm Controller
1–16 CHANNEL GAS DETECTION ALARM CONTROLLER
RD3000E Gas Leakage Detection Alarm Controller
1–16 detector channels•4–20 mA and RS-485 inputs•Audible/visual alarms•Ethernet and relay outputs
Supported channels1–16 compatible detectors
Signal inputsThree-wire 4–20 mA and RS-485 bus detectors
Alarm modesLow, high, and fault alarms
Signal outputsSwitch value, RS-485, Ethernet
Relay outputs2 dry normally-open groups; 10 A at 250 VAC
Main power85–265 VAC, 50/60 Hz
HOW THE PRODUCT WORKS
Centralized multi-point gas detection and alarm control for industrial sites
Multi-channel gas alarm control for industrial safety systems
The RD3000E Gas Leakage Detection Alarm Controller centralizes signals from compatible gas detectors across industrial sites. It supports 1–16 detection channels, accepting three-wire 4–20 mA detectors and RS-485 bus-type detectors, and can upload RS-485 communication data to host software. Depending on the selected detectors, the system can monitor combustible gases, toxic and harmful gases, temperature, and humidity.
Monitor multiple points and identify alarm conditions
A large LCD displays live concentration readings, and users can adjust high and low alarm setpoints. The controller provides low alarm, high alarm, and fault alarm modes. When a configured reading reaches its alarm condition, the controller issues audible and visual alarms and can drive exhaust ventilation or other connected equipment through relay outputs. Detector selection and setpoints must be matched to the target gas and site requirements.
Connect detector signals and control-room systems
The RD3000E accepts three-wire 4–20 mA analog inputs and RS-485 bus-type detectors. Its listed outputs include switch signals, RS-485, and Ethernet. Two groups of dry normally-open relay contacts are specified, rated 10 A at 250 VAC. Confirm compatible detector models, communication protocol, channel allocation, relay loads, and host software interface before system integration.
Alarm history, backup power, and wall mounting
The controller automatically stores at least 10,000 alarm records and uses two-level password management. Main supply is 85–265 VAC, 50/60 Hz; an optional backup supply uses two rechargeable 12 V / 7.2 Ah lead-acid batteries. The wall-mounted enclosure measures 500 × 360 × 122 mm and weighs about 15 kg. Verify environmental limits, mounting clearances, cable routes, and certification documents for the supplied configuration.
For a system quotation, provide the site type, target gases, detector models and quantity, 4–20 mA or RS-485 interfaces, alarm setpoints, relay-driven equipment, Ethernet or host software needs, backup power requirement, and installation environment. This helps match the multi-channel gas detection alarm controller to compatible detector signals and site alarm requirements.
Key product features
Live readings with adjustable alarm setpoints
The large LCD displays live concentration values; high and low alarm setpoints can be adjusted for compatible detector and target gas configurations.
Audible/visual alarms and relay control
Low, high, and fault conditions can trigger audible and visual alarms. Two normally-open dry contact groups are provided for configured external equipment.
RS-485 and Ethernet connectivity
The controller supports RS-485 and Ethernet outputs, including upload of RS-485 detector communication data to host software; confirm protocol and software compatibility.
Alarm history and controlled access
Automatically stores at least 10,000 alarm records and provides two-level password management.
Optional backup supply
Main power operates from 85–265 VAC; an optional backup arrangement uses two 12 V / 7.2 Ah rechargeable lead-acid batteries.
APPLICATIONS
Typical applications
Hydrogen refuelling and production sites
Centralize compatible gas detector signals and alarms across hydrogen station or production facility detection points.
Chemical plants and oil refineries
Monitor configured combustible and toxic gas detection points and route alarms to ventilation or other equipment.
Fuel and gas filling stations
Connect multiple detectors for centralized readings and low/high alarm handling, subject to site design and detector compatibility.
Paint spray booths and industrial plants
Use multi-channel alarm control where industrial risk assessment calls for gas leak monitoring and control-room reporting.
RD3000E Gas Leakage Detection Alarm Controller technical specifications and integration requirements
| Parameter | Specification |
|---|---|
| Model | RD3000E |
| Supported detector channels | 1–16 channels |
| Signal input | Three-wire 4–20 mA analog detectors and RS-485 bus-type detectors |
| Maximum permissible error | ±5% F.S |
| Alarm modes | Low alarm, high alarm, fault alarm |
| Signal outputs | Switch value, RS-485 bus, Ethernet |
| Relay output | 2 groups of dry normally-open contacts; 10 A at 250 VAC |
| Display and alarm settings | Large LCD; live concentration display; adjustable high and low alarm setpoints |
| Alarm record storage | At least 10,000 records |
| Access control | Two-level password management |
| Main power supply | 85–265 VAC, 50/60 Hz |
| Optional backup power | 2 × 12 V / 7.2 Ah rechargeable lead-acid batteries |
| Power consumption | 45 W, excluding detectors |
| Operating temperature | −10 to +55 °C |
| Operating humidity | ≤95% RH; confirm condensation conditions for supplied configuration |
| Mounting | Wall-mounted |
| Dimensions (L × W × H) | 500 × 360 × 122 mm |
| Weight | About 15 kg |
| Certifications stated in product documentation | Explosion-proof, CCCF fire certification, and CE; verify certificates applicable to the supplied configuration |
Confirm the measuring range, output, power supply, and process conditions for your application when requesting a quotation.
What to include in your inquiry
For a project-specific RD3000E Gas Leakage Detection Alarm Controller quotation and application review, share your target measurement range, gas composition, operating temperature and humidity, pressure, installation method, required signal output, and project location. This helps our team assess the right configuration for your hydrogen monitoring or gas analysis system.
Send your application detailsFAQ
Frequently asked questions about RD3000E Gas Leakage Detection Alarm Controller selection and applications
Find guidance on RD3000E Gas Leakage Detection Alarm Controller measuring range, installation, operating conditions, and integration with hydrogen monitoring systems.
How many detectors can the RD3000E support?
The published configuration supports 1–16 detector channels. Confirm the number and type of input modules required for the project.
Which detector signal types are accepted?
The controller accepts three-wire 4–20 mA analog detectors and RS-485 bus-type detectors. Confirm the supported detector models and communication protocol.
What alarms and outputs are available?
The listed alarm modes are low, high, and fault alarms. Outputs include switch value, RS-485, Ethernet, and two groups of dry normally-open relay contacts rated 10 A at 250 VAC.
Can the controller start ventilation equipment?
The product documentation states that alarm outputs can drive exhaust ventilation and other equipment. Verify the connected load, relay arrangement, and safety interlocks with the system designer.
Is backup power available?
An optional backup supply is specified as two rechargeable 12 V / 7.2 Ah lead-acid batteries. Confirm backup runtime and configuration with the supplier.
What details should I provide for a quotation?
Share target gases, detector models and quantity, channel signals, alarm setpoints, relay loads, host software and Ethernet needs, backup supply, site environment, and required certification documents.
Discuss RD3000E Gas Leakage Detection Alarm Controller for your application
Send your operating conditions and project requirements for a technical review and quotation.
Contact the Sales Team